S-7200A SINGLE NEEDLE DIRECT DRIVE STRAIGHT LOCK STITCHER WITH THREAD TRIMMER
S-7200A 3. INSTALLATION43-1. Table processing diagram The top of the table should be 40 mm in thickness and should be strong enough to hold the we
S-7200A 3. INSTALLATION 53. Power switch (1) Power switch (2) Screws [2 pcs] 4. Oil pan (1) Head cushions (left) [2 pcs] (2) Head c
S-7200A 3. INSTALLATION67. Machine head (1) Hinges [2 pcs] (2) Machine head (3) Head rest NOTE: Tap the head rest (3) securely into the table hole.
S-7200A 3. INSTALLATION 711. Knee lifter plate (1) Knee lifter plate (2) Bolt * Loosen the bolt (3) and move the knee lifter plate (1) to a posit
S-7200A 3. INSTALLATION83-3. Lubrication (-40[], 43[] specifications) * If the sewing machine is -45[] specifications, it is a complete dry type mac
S-7200A 3. INSTALLATION 93-4. Connecting the cords DANGER Wait at least 5 minutes after turning off the power switch and disconnecting the pow
S-7200A 3. INSTALLATION10(1) 10-pin operating panel connector (2) 14-pin encoder connector (3) 14-pin machine connector (4) 7-pin head detector un
S-7200A 3. INSTALLATION 113. Other cords (1) 6-pin power supply connector (2) 4-pin motor connector (3) Wire clip (4) Power cord <For single-ph
S-7200A 3. INSTALLATION123-5. Test operation (Operating the treadle) CAUTION Do not touch any of the moving parts or press any objects against
S-7200A 4. PREPARATION BEFORE SEWING 134. PREPARATION BEFORE SEWING 4-1. Installing the needle CAUTION Turn off the power switch before instal
S-7200A iThank you very much for buying a BROTHER sewing machine. Before using your new machine, please read the safety instructions below and the exp
S-7200A 4. PREPARATION BEFORE SEWING 142126M 4-3. Winding the lower thread CAUTION Do not touch any of the moving parts or press any objects a
S-7200A 4. PREPARATION BEFORE SEWING 152128M 4-5. Threading the upper thread CAUTION Turn off the power switch before threading the upper thre
S-7200A 4. PREPARATION BEFORE SEWING 164-7. Using the thread wiper Press the thread wiper switch (1) to the side. If this is done, the thread wipe
S-7200A 5. USING THE OPERATION PANEL (BASIC OPERATIONS) 175. USING THE OPERATION PANEL (BASIC OPERATIONS) 5-1. Names and functions • The operatio
S-7200A 5. USING THE OPERATION PANEL (BASIC OPERATIONS) 18 (6) Fixed stitch key When this key is pressed so that the indicator illuminates, th
S-7200A 5. USING THE OPERATION PANEL (BASIC OPERATIONS) 195-2. Sewing start and end backtack stitches 1 Setting start backtack stitches
S-7200A 5. USING THE OPERATION PANEL (BASIC OPERATIONS) 205-3. Sewing fixed stitches 1 From 1 to 1999 stitches can be set
S-7200A 5. USING THE OPERATION PANEL (BASIC OPERATIONS) 215-4. Sewing name labels 1 From 1 to 1999 stitches can be set for t
S-7200A 5. USING THE OPERATION PANEL (BASIC OPERATIONS) 225-5. Sewing pleat presser stitches 1 From 1 to 1999 stitche
S-7200A 5. USING THE OPERATION PANEL (BASIC OPERATIONS) 235-6. Using the lower thread counter The lower thread counter can be used to let you know
S-7200A ii2. Notes on safety DANGER Wait at least 5 minutes after turning off the power switch and disconnecting the power cord from the wall outlet
S-7200A 6. USING THE OPERATION PANEL (ADVANCED OPERATIONS) 246. USING THE OPERATION PANEL (ADVANCED OPERATIONS) The operations described in this sec
S-7200A 6. USING THE OPERATION PANEL (ADVANCED OPERATIONS)256-2. Adjusting the needle up stop position 1. While pressing the needle up/down key (1),
S-7200A 7. SEWING 267. SEWING CAUTION Attach all safety devices before using the sewing machine. If the machine is used without these devices
S-7200A 7. SEWING 277-3. Sewing condensed stitches If you press the actuator (1) or the reverse lever (2) while sewing is in progress, you can sew
S-7200A 8. THREAD TENSION 288. THREAD TENSION 8-1. Adjusting the thread tension CAUTION Turn off the power switch before removing or inserting
S-7200A 8. THREAD TENSION 298-2. Adjusting the presser foot pressure Correct stitches Upper thread Skipped stitches occur Inc
S-7200A 9. CLEANING 309. CLEANING CAUTION Turn off the power switch before carrying out cleaning. The machine may operate if the treadle is
S-7200A 9. CLEANING 312. Lubrication A. Gearbox oil quantity NOTE: Check the quantity of oil in the gearbox immediately after tilting back the mac
S-7200A 9. CLEANING 32B. Oil tank oil quantity (-40[], 43[] specifications) Check the oil gauge window (1), and add more oil if the oil gauge (2) is
S-7200A 9. CLEANING 339-2. Applying grease (When “GREASEUP” appears) If “GREASEUP" flashes on the main display (1) and a buzzer sounds when the
S-7200A iii CAUTION Sewing This sewing machine should only be used by operators who have received the necessary training in safe use befo
S-7200A 9. CLEANING 34 1. Turn the power switch to “OFF”. 2. Remove the screws and the set screws. 3. Apply g
S-7200A 10. TROUBLESHOOTING 3510. TROUBLESHOOTING Please check the following points before calling for repairs or service. If the following reme
S-7200A 10. TROUBLESHOOTING 36 Problem Possible cause Page 5 Skipped stitches at sewing start Thread unravelling at sewing start Is the thread ta
S-7200A 10. TROUBLESHOOTING 37 Problem Possible cause Page 9 Lower thread is tangled at the sewing start. Spinning of bobbin during thread trimming
S-7200A 10. TROUBLESHOOTING 38 Problem Possible cause Page 13 Broken needles Is the material being pushed or pulled with excessive force during s
S-7200A 10. TROUBLESHOOTING 39 Problem Possible cause Page 19 “GREASEUP” flashes on the operation panel when the power is turned on. This display
S-7200A 10. TROUBLESHOOTING 40 Error code Possible cause Page Err 4 Is the motor connector disconnected from the control box? Insert the conn
INSTRUCTION MANUAL □ 877-S20SA2016-0012003.02.B(1)
S-7200A iv3.Warning labels The following warning labels appear on the sewing machine. Please follow the instructions on the labels at all times when
S-7200A CONTENTS 1. NAMES OF MAJOR PARTS... 1 2. MACHINE SPECIFICATIONS... 2 3. INSTALLATION ...
S-7200A 1. NAMES OF MAJOR PARTS 11. NAMES OF MAJOR PARTS (1) Bobbin winder (2) Thread wiper (3) L
S-7200A 2. MACHINE SPECIFICATIONS 22. MACHINE SPECIFICATIONS 4 Quick reverse ○ Thread wiper ○ 0 3 5 Lubrication type Minimum lubrication Sem
S-7200A 3. INSTALLATION 33. INSTALLATION CAUTION Machine installation should only be carried out by a qualified technician. Contact your
Kommentare zu diesen Handbüchern