Brother Laser PrinterHL-6050HL-6050DHL-6050DNUser's GuideVersion 2For visually-impaired usersYou can read this manual with Screen Reader ‘text-to
ABOUT THIS PRINTER 1 - 2Front viewFront view Figure 1-21Face down output tray support flap (support flap)2Control panel3Multi-purpose tray (MP tray)
CONTROL PANEL 3 - 29Braille symbolsThe control panel buttons are marked with Braille characters for visually-impaired users as shown in the table.*B
4 - 1 OPTIONS4Optional accessories and suppliesThis printer has the following optional accessories. You can increase the capabilities of the printer
OPTIONS 4 - 2Lower tray unit (LT-6000)The lower tray unit (Tray 2) is an optional device that can hold up to 500 sheets of paper (80 g/m2 or 20 lb).
4 - 3 OPTIONSNetwork board (NC-6100h) (For HL-6050 and HL-6050D)Installing the Brother network board (NC-6100h) allows you to connect the printer on
OPTIONS 4 - 44Loosen the two screws, and then remove the Network cover plate. Figure 4-45Put the network board connector firmly into the connector o
4 - 5 OPTIONS7Put the side cover back on.Figure 4-78Connect one end of the ethernet cable to the network port of the printer.9Plug the printer back
OPTIONS 4 - 6Wireless print server (NC-7100w)The Brother NC-7100w wireless print server supports the IEEE 802.11b and 802.11g wireless networking st
4 - 7 OPTIONS4Loosen the two screws, and then remove the Network cover plate. Figure 4-105Put the NC-7100w print server connector firmly into the co
OPTIONS 4 - 89Make sure that the POWER LED of the print server is on.Figure 4-1210For details about how to use the NC-7100w wireless print server, p
4 - 9 OPTIONSCompactFlash® cardThis printer has a slot for an optional industry standard CompactFlash® card, which is a memory card.If you install a
1 - 3 ABOUT THIS PRINTERBack viewBack view*Figure 1-31Face up output tray (back output tray)2Face up output tray support3AC power connector4Power sw
OPTIONS 4 - 10Inserting the CompactFlash® card Follow these steps to insert or remove a card: 1Turn off the printer power switch, and then unplug th
4 - 11 OPTIONSDIMMThe HL-6050, HL-6050D and HL-6050DN printers have 32 MB of standard memory and one slot for optional memory expansion. You can exp
OPTIONS 4 - 12Installing additional memoryWhen you install extra memory, follow these steps: 1Turn off the printer power switch, and then unplug the
4 - 13 OPTIONS5Hold the DIMM on the side edges. Line up the notches on the DIMM with the DIMM slot. (Check that the locks on each side of the DIMM s
OPTIONS 4 - 148Put the side cover back on.Figure 4-199Reconnect the interface cable to your printer. Plug the printer back in, and then turn on the
4 - 15 OPTIONSOptional fonts packageOptional fonts package (BS-3000)The optional font package (BS-3000) is the CD-ROM you need for installing the 13
ROUTINE MAINTENANCE 5 - 15Replacing the consumable itemsYou will need to replace the consumable items regularly. When the time comes to replace cons
5 - 2 ROUTINE MAINTENANCEToner cartridge A new toner cartridge contains enough toner to print up to 7,500 A4 or Letter size single-sided pages at ab
ROUTINE MAINTENANCE 5 - 3Replacing the toner cartridge1Press the cover release button and then open the front cover of the printer.Figure 5-12Take o
5 - 4 ROUTINE MAINTENANCECaution We recommend that you place the drum unit assembly on a piece of disposable paper or cloth in case you accidentall
ABOUT THIS PRINTER 1 - 4Positioning the printerPlease read the following before you use the printer.Power supplyUse the printer within the recommend
ROUTINE MAINTENANCE 5 - 54Unpack the new toner cartridge. Hold the cartridge level with both hands and gently rock it from side to side five or six
5 - 6 ROUTINE MAINTENANCECautionPut the toner cartridge in the drum unit immediately after you have removed the protective cover. To prevent degrada
ROUTINE MAINTENANCE 5 - 78Clean the primary corona wire inside the drum unit by gently sliding the blue tab from right to left and left to right sev
5 - 8 ROUTINE MAINTENANCEDrum unitThis printer can print up to 30,000 pages* with one drum unit.* At 5% print coverage (A4 or Letter size). The actu
ROUTINE MAINTENANCE 5 - 91Press the cover release button and then open the front cover of the printer.Figure 5-122Take out the drum unit assembly (d
5 - 10 ROUTINE MAINTENANCE3Push down the blue lock lever and take the toner cartridge out of the drum unit assembly.Figure 5-15CautionDo not touch t
ROUTINE MAINTENANCE 5 - 115Put the toner cartridge firmly into the new drum unit until you hear it lock into place. If you put the cartridge in prop
5 - 12 ROUTINE MAINTENANCE8Reset the drum counter. See the instructions supplied with the new drum unit.CautionDo not reset the drum counter when yo
ROUTINE MAINTENANCE 5 - 13Replacing Maintenance PartsYou will need to replace the maintenance parts regularly to maintain print quality. When it is
5 - 14 ROUTINE MAINTENANCECleaningClean the outside and inside of the printer with a dry soft cloth. When you replace the drum unit, make sure you c
1 - 5 ABOUT THIS PRINTERWhat kind of paper can I use?Type and size of paperThe printer loads paper from the installed paper tray, manual feed tray (
ROUTINE MAINTENANCE 5 - 15Cleaning the inside of the printerClean the inside of the printer as follows: 1Turn off the printer power switch, and then
5 - 16 ROUTINE MAINTENANCE4Wipe the scanner window with a dry, soft cloth.Figure 5-265Put the drum unit assembly in the printer.6Close the front cov
ROUTINE MAINTENANCE 5 - 17Cleaning the corona wireIf you are experiencing print quality problems, please clean the corona wire as follows:1Turn off
6 - 1 TROUBLESHOOTING6LCD messagesIf any problems occur, the printer automatically stops printing, diagnoses the problem, and displays the resulting
TROUBLESHOOTING 6 - 2FRONT COVER OPEN Close the front cover of the printer.FUSER COVER OPEN Close the jam clear cover located behind the back output
6 - 3 TROUBLESHOOTINGMaintenance messagesMaintenance message ActionCHANGE DRUM SOON The drum unit is almost at the end of life. Prepare a new drum u
TROUBLESHOOTING 6 - 4Troubleshooting paper handling First, make sure that you are using paper that meets our recommended paper specifications. See W
6 - 5 TROUBLESHOOTINGPaper jams and how to clear themIf paper jams inside the printer, the printer will stop. One of the following LCD messages will
TROUBLESHOOTING 6 - 6JAM MP TRAY (paper jam in the multi-purpose tray)If there is a paper jam in the multi-purpose tray, follow these steps: 1Press
6 - 7 TROUBLESHOOTINGJAM TRAY 1 / TRAY 2(Paper jam inside the Paper tray)If a paper jam occurs inside the paper tray, follow these steps: 1Pull the
ABOUT THIS PRINTER 1 - 6You must use the face up output tray (back output tray) for certain print media.When looking at this page on the CD-ROM, you
TROUBLESHOOTING 6 - 82Use both hands to slowly pull out the jammed paper. Figure 6-43Put paper below the maximum paper mark (▼). While pressing the
6 - 9 TROUBLESHOOTINGJAM INSIDE (paper jam inside the printer)If a paper jam occurs inside the printer, follow these steps:1Press the cover release
TROUBLESHOOTING 6 - 10Caution After you have removed the jammed paper, print a few test pages. This is to make sure that the printed pages have no
6 - 11 TROUBLESHOOTINGCaution Handle the toner cartridge carefully. If toner scatters on your hands or clothes, wipe or wash it off with cold water
TROUBLESHOOTING 6 - 12JAM REAR (paper jam behind the back output tray)When the paper jams behind the face-up output tray, remove the jammed paper as
6 - 13 TROUBLESHOOTINGCaution We recommend that you place the drum unit assembly on a piece of disposable paper or cloth in case you accidentally s
TROUBLESHOOTING 6 - 145Push down the blue tabs at the left and right hand sides.Figure 6-206Open the jam clear cover by pushing the levers inward at
6 - 15 TROUBLESHOOTINGJAM DUPLEX (paper jam in the duplex unit)Follow the instructions below to clear a paper jam:1Open the back output tray.Figure
TROUBLESHOOTING 6 - 164Pull the duplex tray and paper tray out of the printer.Figure 6-245Pull the jammed paper out of the printer. Figure 6-256Put
6 - 17 TROUBLESHOOTINGImproving the print quality This section provides information on the following topics.If the same problem occurs again, call y
1 - 7 ABOUT THIS PRINTERRecommended paper Before you buy a lot of paper, please test some to make sure that the paper is suitable. Use paper that
TROUBLESHOOTING 6 - 18Hollow print Make sure that you use paper that meets our specifications. See What kind of paper can I use? on page 1-5. Choo
6 - 19 TROUBLESHOOTINGBlack lines down the pagePrinted pages have toner stains stripes down the page. You may clear the problem by cleaning the pri
TROUBLESHOOTING 6 - 20Black toner marks across the page The drum unit may be damaged. Put in a new drum unit. See Replacing the drum unit on page 5
6 - 21 TROUBLESHOOTINGWhite Spots on black text and graphics at 94 mm (3.7 in.) intervalsBlack Spots at 94 mm (3.7 in.) intervals If the problem is
TROUBLESHOOTING 6 - 22Solving print problemsProblem RecommendationThe printer prints unexpectedly or it prints garbage data. Make sure the interfac
6 - 23 TROUBLESHOOTINGOther problemsPrinting from DOS BR-Script 3CautionIf you do not follow the instructions for using the printer, you may be resp
APPENDIX (SPECIFICATIONS, FONTS AND BAR CODE) A - 1APrinter specifications* For HL-6050D and HL-6050DNAppendix (Specifications, fonts and bar code)E
A - 2 APPENDIX (SPECIFICATIONS, FONTS AND BAR CODE)* Instructional animations for problem solving** The Driver Deployment Wizard automates the insta
APPENDIX (SPECIFICATIONS, FONTS AND BAR CODE) A - 3* Calculated with 80 g/m2 or 20 lb. paper** Up to 10 sheetsPaper handlingPaper input*Multi-purpos
A - 4 APPENDIX (SPECIFICATIONS, FONTS AND BAR CODE)* USB is not supported under Windows® 95 or Windows NT®4.0.** Power Macintosh with an Apple origi
ABOUT THIS PRINTER 1 - 8Printable areaWhen using PCL (standard driver) emulation, the edges of the paper that cannot be printed on are shown below.P
APPENDIX (SPECIFICATIONS, FONTS AND BAR CODE) A - 5Important information for choosing your paperThis section provides information to help you choose
A - 6 APPENDIX (SPECIFICATIONS, FONTS AND BAR CODE)Moisture contentMoisture content is the amount of water left in the paper after manufacture. It i
APPENDIX (SPECIFICATIONS, FONTS AND BAR CODE) A - 7Quick reference for bar code control commands The printer can print bar codes in the HP LaserJet,
A - 8 APPENDIX (SPECIFICATIONS, FONTS AND BAR CODE)Bar Code, expanded character, line block drawing and box drawing n = 's0' or 'S0 3
APPENDIX (SPECIFICATIONS, FONTS AND BAR CODE) A - 9Bar code human readable line ON or OFFn = 'r0' or 'R0 Human readable line OFFn = &
A - 10 APPENDIX (SPECIFICATIONS, FONTS AND BAR CODE)Bar code, expanded character, line block drawing and box drawing heightn = 'hnnn', &ap
APPENDIX (SPECIFICATIONS, FONTS AND BAR CODE) A - 11 When Interleaved 2 of 5 is selected with the parameter 't1' or 'T1': Ten n
A - 12 APPENDIX (SPECIFICATIONS, FONTS AND BAR CODE) When Codebar is chosen with the parameter 't9' or 'T9' Characters '0&
APPENDIX (SPECIFICATIONS, FONTS AND BAR CODE) A - 13Expanded character data startn = 'l' or 'L'Data that follows 'l' o
B - 1 APPENDIX (FOR EUROPE AND OTHER COUNTRIES)BBrother NumbersIMPORTANT: For technical and operational help, you must call the country where you bo
1 - 9 ABOUT THIS PRINTERLandscapeFigure 1-6A4 Letter Legal B5 (ISO) Executive A5 A6 B6 (ISO)14.2 mm (0.17 in.)4.2 mm (0.17 in.)4.2 mm (0.17 in.)4.2
APPENDIX (FOR EUROPE AND OTHER COUNTRIES) B - 2Important information: RegulationsRadio interference (220 to 240 volt model only)This printer follows
B - 3 APPENDIX (FOR EUROPE AND OTHER COUNTRIES)IMPORTANT - For Your SafetyTo ensure safe operation the supplied three-pin plug must be inserted only
APPENDIX (FOR EUROPE AND OTHER COUNTRIES) B - 4EC Declaration of ConformityManufacturerBrother Industries Ltd.,15-1, Naeshiro-cho, Mizuho-ku,Nagoya
APPENDIX (FOR USA AND CANADA) C - 1CBrother NumbersIMPORTANT: For technical and operational help, you must call the country where you bought the pri
C - 2 APPENDIX (FOR USA AND CANADA)Brother fax back system (USA only)Brother has installed an easy to use fax back system so you can get instant ans
APPENDIX (FOR USA AND CANADA) C - 3Important information: RegulationsFederal Communications Commission (FCC) Declaration of Conformity (For USA)Resp
C - 4 APPENDIX (FOR USA AND CANADA)Industry Canada Compliance Statement (For Canada)This Class B digital apparatus complies with Canadian ICES-003.C
APPENDIX (FOR USA AND CANADA) C - 5IMPORTANT - For Your SafetyTo ensure safe operation the supplied three-pin plug must be inserted only into a stan
I - 1IndexSymbols+ or - buttons ...3-7AAccessories and supplies ... C-2Accesso
I - 2PRINT menu ...3-25, 3-26PRINT MENU menu ...3-17Print quality ...
ABOUT THIS PRINTER 1 - 10Printing methodsPrinting on plain paper You can print on plain paper from the paper tray or multi-purpose tray. For the pap
1 - 11 ABOUT THIS PRINTER2Pull the paper tray completely out of the printer.Figure 1-73While pressing the blue paper-guide release lever, slide the
iDefinitions of warnings, cautions, and notesWe use the following terms throughout this User’s Guide:You must follow these warnings to prevent possib
ABOUT THIS PRINTER 1 - 125Put the paper tray firmly back in the printer. Check that it is inserted fully into the printer.Figure 1-116Send the print
1 - 13 ABOUT THIS PRINTERPrinting on plain paper from the multi-purpose tray (MP tray)1Select the Paper Size, Media Type, Paper Source, and other se
ABOUT THIS PRINTER 1 - 142Open the MP tray and lower it gently.Figure 1-133Pull out the MP tray support flap.Figure 1-144Put paper in the MP tray. P
1 - 15 ABOUT THIS PRINTER5While pressing the paper-guide release lever, slide the paper guide to fit the paper size.Figure 1-166Send the print data
ABOUT THIS PRINTER 1 - 16Printing on thick paper, labels and card stock Do not use damaged, curled, wrinkled, or irregularly shaped paper. Do not
1 - 17 ABOUT THIS PRINTERPrinting on thick paper, labels or card stock from the multi-purpose tray (MP tray)When the back output tray is pulled down
ABOUT THIS PRINTER 1 - 182Open the back output tray, and then pull out the face up output tray support if necessary.Figure 1-203Open the MP tray and
1 - 19 ABOUT THIS PRINTER5Put paper in the MP tray. Put the side to be printed on first, face up, with the leading edge (top) of the paper in first.
ABOUT THIS PRINTER 1 - 20CautionRemove each sheet immediately after printing. Stacking the sheets may cause a paper jam or the paper to curl.Figure
1 - 21 ABOUT THIS PRINTERPrinting on envelopes Types of envelopes to avoidDo not use envelopes which: are damaged, curled, wrinkled, or an usual sh
ii To use the printer safelyCaution Use neutral detergents for cleaning. Cleaning with volatile liquids such as thinner or benzene will damage the
ABOUT THIS PRINTER 1 - 22Most envelopes will be suitable for your printer. However, some envelopes will have feed and print quality problems due to
1 - 23 ABOUT THIS PRINTERPrinting on envelopes from the MP tray When the back output tray is pulled down, the printer has a straight paper path from
ABOUT THIS PRINTER 1 - 242Open the back output tray, and then pull out the face up output tray support if necessary.Figure 1-283Open the MP tray and
1 - 25 ABOUT THIS PRINTER5Put envelopes in the MP tray so that they touch the back of the tray and remain under the maximum paper height guides on b
ABOUT THIS PRINTER 1 - 266Press and slide the paper width guide to fit the envelope size.Figure 1-337Send the print data to the printer.8After you f
1 - 27 ABOUT THIS PRINTER If envelopes get smudged during printing, in the printer driver select MP Tray as the Paper Source for a straight paper p
ABOUT THIS PRINTER 1 - 28Printing on transparenciesYou can print on transparencies from the paper tray or MP tray.Printing on transparencies from th
1 - 29 ABOUT THIS PRINTER2Pull the paper tray completely out of the printer.Figure 1-343While pressing the blue paper guide release levers, slide th
ABOUT THIS PRINTER 1 - 305Put the paper tray firmly back in the printer. Check that it is inserted fully into the printer.Figure 1-386Send the print
1 - 31 ABOUT THIS PRINTERPrinting on transparencies from the MP tray When the back output tray is pulled down, the printer has a straight paper path
iiiTrademarksThe Brother logo is a registered trademark of Brother Industries, Ltd. Apple, the Apple Logo and Macintosh are registered trademarks in
ABOUT THIS PRINTER 1 - 322Open the back output tray, and then pull out the face up output tray support if necessary.Figure 1-403Open the MP tray and
1 - 33 ABOUT THIS PRINTER5Put transparencies in the MP tray. Put the side to be printed on first, face up, with the leading edge (top) of the paper
ABOUT THIS PRINTER 1 - 347Send the print data to the printer.8After you finish printing, close the back output tray.CautionRemove each transparency
1 - 35 ABOUT THIS PRINTERPrinting on both sides of the paperThe supplied printer drivers for Windows® 95/98/Me, Windows NT® 4.0, Windows® 2000/XP, M
ABOUT THIS PRINTER 1 - 36Manual duplex printing from the multi-purpose trayCaution Before putting the sheets back in the MP tray, you will have to
1 - 37 ABOUT THIS PRINTERAutomatic duplex printing (available for HL-6050D and HL-6050DN only)CautionUse A4, Letter or Legal size paper when you use
ABOUT THIS PRINTER 1 - 383For the PCL (standard) printer driverOpen the Properties dialog box in the printer driver. Choose the General tab and clic
1 - 39 ABOUT THIS PRINTERBooklet printing (for the PCL printer driver)(available for HL-6050D and HL-6050DN only)1Put paper in the paper tray or MP
ABOUT THIS PRINTER 1 - 40Guidelines for printing on both sides of the paper If the paper is thin, it may wrinkle. If paper is curled, straighten i
1 - 41 ABOUT THIS PRINTERPaper orientation for printing on both sides of the paper (for automatic duplex printing)The printer prints the second page
ivTable of ContentsDefinitions of warnings, cautions, and notes ...
ABOUT THIS PRINTER 1 - 42Carbon copy printingCarbon copy printing enables you to automatically print one page data to different styles of paper by c
2 - 1 DRIVER AND SOFTWARE2Printer driver A printer driver is software that translates data from the format used by a computer to the format that a p
DRIVER AND SOFTWARE 2 - 2For Windows® Features in the PCL printer driverYou can download the latest printer driver or get other information by acces
2 - 3 DRIVER AND SOFTWAREAdvanced tabChange the tab settings by clicking the following icons:1Print Quality2Duplex3Watermark 4Page Setting5Device Op
DRIVER AND SOFTWARE 2 - 4Print QualitySelect the resolution, toner save and print settings, or gray printing setting.ResolutionYou can change the re
2 - 5 DRIVER AND SOFTWAREDevice OptionsYou can set the following Printer Function modes in this tab:(You can jump to the page for each Printer Funct
DRIVER AND SOFTWARE 2 - 6Job SpoolingThe printer saves data that you want reprinted.You can reprint a document without sending the data again from y
2 - 7 DRIVER AND SOFTWAREPage Protection‘Page Protection’ refers to a setting that reserves additional memory for the creation of full page images.S
DRIVER AND SOFTWARE 2 - 8Accessories tab When you install the optional lower tray unit and other options, you can add it and select its settings in
2 - 9 DRIVER AND SOFTWARESupport tab1Displays the printer driver version.2Web UpdateYou can check the brother web site for updated drivers and autom
v3Control panel ...
DRIVER AND SOFTWARE 2 - 10Features in the BR-Script printer driver (PS printer driver)You can download the latest driver by accessing the Brother So
2 - 11 DRIVER AND SOFTWAREDevice Settings tab Select the options you have installed.
DRIVER AND SOFTWARE 2 - 12Layout tabYou can change the layout setting by selecting the settings for Orientation, Print on Both Sides (Duplex), Page
2 - 13 DRIVER AND SOFTWAREPaper / Quality tabSelect the Paper Source.
DRIVER AND SOFTWARE 2 - 14Advanced options1Select the Paper Size and Copy Count.2Set the Print Quality, Scaling and TrueType Font settings.3You can
2 - 15 DRIVER AND SOFTWAREToner SaveYou can save running costs by turning on the Toner Save, which reduces the print density.Sleep TimeWhen the prin
DRIVER AND SOFTWARE 2 - 16For Macintosh® This printer supports Mac OS® 8.6 to 9.2 and Mac OS® X 10.1, 10.2 or greater.You can download the latest dr
2 - 17 DRIVER AND SOFTWARESpecific settingsYou can change settings by selecting the setting in the Printer Features list: Media Type Resolution H
DRIVER AND SOFTWARE 2 - 18Sleep TimeWhen the printer does not receive data for a certain period of time (timeout), it enters sleep mode. Sleep mode
2 - 19 DRIVER AND SOFTWARESoftware (Windows® users)Software for NetworksBRAdmin ProfessionalThe BRAdmin Professional is a utility for managing your
vi5Routine maintenance ...
DRIVER AND SOFTWARE 2 - 20Automatic emulation selectionThis printer has an automatic emulation selection feature. When the printer receives data fro
2 - 21 DRIVER AND SOFTWAREPrinter settingsFactory settingsThe printer settings have been set at the factory before shipment. They are called factory
CONTROL PANEL 3 - 13Control panelThis printer has one liquid crystal display (LCD), seven buttons and one Light Emitting Diode (LED) on the control
3 - 2 CONTROL PANELButtons You can control the basic printer operations and change various printer settings with seven buttons (Go, Job Cancel, Repr
CONTROL PANEL 3 - 3Reprint buttonIf you want to reprint a document that has just been printed, you can reprint it by pressing the Reprint button. Al
3 - 4 CONTROL PANELReprint the last job three times1Make sure the REPRINT setting is ON by using the control panel buttons to enter the SETUP menu.
CONTROL PANEL 3 - 5Printing Public dataYou can use this setting to reprint documents that are stored in a Public area of the printer memory. Documen
3 - 6 CONTROL PANELHow to print Secure dataWhen there is no reprint data in memoryIf the printer does not have reprint data in the memory and you pr
CONTROL PANEL 3 - 7+ or - buttonIf you press the + or - button when the printer is online (READY), it goes offline and the LCD displays the menu. To
3 - 8 CONTROL PANELLight-emitting diode (LED)The LED is a light which shows the printer status. Data - Orange LEDLED indication MeaningOn Data is in
viiInternal laser radiation ...B-2IMPORTANT -
CONTROL PANEL 3 - 9Liquid Crystal Display (LCD) The display shows the current printer status. When you use the control panel buttons, the display wi
3 - 10 CONTROL PANELLCD messagePrinter status messagesThe following table shows the printer status messages that are displayed during normal operati
CONTROL PANEL 3 - 11How to use the control panelWhen you use the Menu buttons (+, -, Set or Back), remember the following basic steps: If no contr
3 - 12 CONTROL PANELFor example: If you feed paper from the MP tray as a priority, change the MP FIRST setting to ON as follows.The default setting
CONTROL PANEL 3 - 13Control Panel LCD menu Standard paper tray: TRAY 1 Multi-purpose tray: MP TRAY Optional lower tray: TRAY 2There are eight men
3 - 14 CONTROL PANELINFORMATIONDisplay Shows DescriptionPRINT SETTINGS Prints the print settings page.PRINT TEST Prints the test page.PRINT DEMO Pri
CONTROL PANEL 3 - 15PAPERDisplay Shows DescriptionSOURCE =AUTO/MP/TRAY1/TRAY2Selects which paper tray the paper will be fed from.PRIORITY =MP>T1&
3 - 16 CONTROL PANELSETUPDisplay Shows DescriptionLANGUAGE = ENGLISH /FRANÇAIS /...PANEL CONTROL Subsetting DescriptionLCD DENSITY =0/1/2AUTO ONLINE
CONTROL PANEL 3 - 17PRINT MENUDisplay Shows DescriptionMEDIA TYPE =PLAIN PAPER, TRANSPARENCIES, THICK PAPER, THICKER PAPER, THIN PAPER, BOND PAPER,
3 - 18 CONTROL PANELHP LASERJET(continued)Subsetting DescriptionRIGHT MARGIN =##Sets the right margin at column 10 to 80 columns at 10 cpi.TOP MARGI
1 - 1 ABOUT THIS PRINTER1What is in the box?When you unpack the printer, check to see that you have all of the following parts.1Printer2Drum unit as
CONTROL PANEL 3 - 19IBM PROPRINTER Subsetting DescriptionFONT NO. =I000 ... ####FONT PITCH =##.##CHARACTER SET PC-8/...Sets the symbol set or the ch
3 - 20 CONTROL PANELNETWORK (only on a Network)Display Shows DescriptionTCP/IP Subsetting DescriptionTCP/IP ENABLE =ON/OFFIP ADDRESS= ###.###.###.##
CONTROL PANEL 3 - 21INTERFACEDisplay Shows DescriptionSELECT =AUTO/PARALLEL/USB/NETWORKAUTO IF TIME = 1, 2, 3 ... 99 (sec)You need to set the time-o
3 - 22 CONTROL PANELSet IP AddressPress the + or - button until NETWORK appears (and to display each setting shown below).Press the Set button.Press
CONTROL PANEL 3 - 23About emulation modesThis printer has the following emulation modes. HP LaserJet ModeThe HP LaserJet mode (or HP mode) is the em
3 - 24 CONTROL PANELList of factory settingsTable 3-1 shows the factory settings. Network factory default settingIf you wish to reset the print serv
CONTROL PANEL 3 - 25Table 3 - 1: List of factory settings Display Shows Submenu Factory settingPAPER SOURCE =AUTOPRIORITY =MP>T1>T2MP FIRST =O
3 - 26 CONTROL PANELPRINT MENU (continued)HP LASERJET Subsetting Factory settingFONT NO. =59FONT PITCH =10.00/12.00SYMBOLSET =PC8AUTO LF =OFFAUTO CR
CONTROL PANEL 3 - 27*1 Automatic Private IP Addressing (APIPA) protocol automatically configures an IP address and subnet mask. For more details, se
3 - 28 CONTROL PANELFor visually-impaired usersBuzzer indicationsThe control panel has a buzzer. The buzzer will sound when one of the control panel
Kommentare zu diesen Handbüchern