Brother S-7200C Bedienerhandbuch

S-7200C Please read this manual before using the machine. Please keep this manual within easy reach for quick reference. SINGLE NEEDLE DIRECT DRIV

S-7200C 3. INSTALLATION 3 3. INSTALLATION CAUTION Machine installation should only be carried out by a qualified technician. Contact you

S-7200C 3. INSTALLATION43-1. Table processing diagram  The top of the table should be 40 mm in thickness and should be strong enough to hold the we

S-7200C 3. INSTALLATION 5 3. Oil pan (1) Head cushions (left) [2 pcs] (2) Head cushions (right) [2 pcs] (3) Oil pan 4. Rubber

S-7200C 3. INSTALLATION67. Operation panel (1) Operation panel (2) Screws [2 pcs] (Use for tightening rear cover) 8. Sticker (Remove

S-7200C 3. INSTALLATION 7 10. Knee lifter plate (1) Knee lifter plate (2) Bolt * Loosen the bolt (3) and the bolt (4), and then adjust the positi

S-7200C 3. INSTALLATION83-3. Lubrication (-[]0[], []3[] specifications) * If the sewing machine is -[]5[] specifications, it is a complete dry type

S-7200C 3. INSTALLATION 9 3-4. Connecting the cords DANGER Wait at least 5 minutes after turning off the power switch and disconnecting the po

S-7200C 3. INSTALLATION10(1) 6-pin head detector unit connector (2) 12-pin operation panel connector (3) 10-pin resolver connector (4) 14-pin ma

S-7200C 3. INSTALLATION 11 3. Ground wire (1) Ground wire (2) Washer (3) Spring washer (4) Screw 4. Other cords Connect cords that m

S-7200C 3. INSTALLATION12<200 V system > (1) Power switch (2) Screws [2 pcs] (3) 3-pin power supply connector (4) Power cord (5)

S-7200C Thank you very much for buying a BROTHER sewing machine. Before using your new machine, please read the safety instructions and the explanat

S-7200C 3. INSTALLATION 13 <100 V/400 V system > (1) Power switch (2) Screws [2 pcs] (3) Transformer box (4) Transformer box plate

S-7200C 3. INSTALLATION143-5. Test operation (Operating the treadle) CAUTION Do not touch any of the moving parts or press any objects agains

S-7200C 4. PREPARATION BEFORE SEWING 15 4. PREPARATION BEFORE SEWING 4-1. Installing the needle CAUTION Turn off the power switch before insta

S-7200C 4. PREPARATION BEFORE SEWING 162126M4-3. Winding the lower thread CAUTION Do not touch any of the moving parts or press any objects ag

S-7200C 4. PREPARATION BEFORE SEWING 17 4-5. Threading the upper thread CAUTION Turn off the power switch before threading the upper thread.

S-7200C 4. PREPARATION BEFORE SEWING 184156M4-6. Adjusting the stitch length 1. Push the dial lock lever (1) up until it clicks to release the lock

S-7200C 5. USING THE G50 OPERATION PANEL (BASIC OPERATIONS) 19 5. USING THE G50 OPERATION PANEL (BASIC OPERATIONS) 5-1. Names and functions • The o

S-7200C 5. USING THE G50 OPERATION PANEL (BASIC OPERATIONS) 20 (7) Name label key When this key is pressed so that the indicator illuminates, f

S-7200C 5. USING THE G50 OPERATION PANEL (BASIC OPERATIONS) 21 5-2. Sewing start and end backtack stitches 1 Setting start backtack sti

S-7200C 5. USING THE G50 OPERATION PANEL (BASIC OPERATIONS) 225-3. Sewing continuous backtack stitches 1 Setting continuous backtack sti

S-7200C i SAFETY INSTRUCTIONS [1] Safety indications and their meanings This instruction manual and the indications and symbols that are used on the

S-7200C 5. USING THE G50 OPERATION PANEL (BASIC OPERATIONS) 23 5-4. Sewing fixed stitches 1 Setting the number of fixed stitches

S-7200C 5. USING THE G50 OPERATION PANEL (BASIC OPERATIONS) 245-5. Sewing name labels 1 Setting the number of name label stitches

S-7200C 5. USING THE G50 OPERATION PANEL (BASIC OPERATIONS) 25 5-6. Sewing pleat presser stitches 1 From 1 to 1999 st

S-7200C 5. USING THE G50 OPERATION PANEL (BASIC OPERATIONS) 265-7. Using the lower thread counter y The lower thread counter can be used to let you

S-7200C 6. USING THE G50 OPERATION PANEL (ADVANCED OPERATIONS) 27 6. USING THE G50 OPERATION PANEL (ADVANCED OPERATIONS) The operations described in

S-7200C 6. USING THE G50 OPERATION PANEL (ADVANCED OPERATIONS) 286-2. Adjusting the needle up stop position 1 (While pressing the

S-7200C 6. USING THE G50 OPERATION PANEL (ADVANCED OPERATIONS) 29 6-3. LOCK key When the power switch is turned on, the LOCK key (1) turns ON. (The

S-7200C 6. USING THE G50 OPERATION PANEL (ADVANCED OPERATIONS) 306-4. Resetting all settings to their defaults If the sewing machine stops operating

S-7200C 7. USING THE G10 OPERATION PANEL (BASIC OPERATIONS) 31 7. USING THE G10 OPERATION PANEL (BASIC OPERATIONS) 7-1. Names and functions ࡮The op

S-7200C 7. USING THE G10 OPERATION PANEL (BASIC OPERATIONS) 327-2. Sewing start and end backtack stitches 1 Setting start backtack stitches

S-7200C ii [2] Notes on safety DANGER Wait at least 5 minutes after turning off the power switch and disconnecting the power cord from the wall outl

S-7200C 7. USING THE G10 OPERATION PANEL (BASIC OPERATIONS) 33 7-3. Sewing continuous backtack stitches 1 Setting continuous backtack stitc

S-7200C 8. USING THE G10 OPERATION PANEL (ADVANCED OPERATIONS) 348. USING THE G10 OPERATION PANEL (ADVANCED OPERATIONS) The operations described in

S-7200C 8. USING THE G10 OPERATION PANEL (ADVANCED OPERATIONS) 35 8-2. Slow start When the slow start setting is enabled, the two stitches at the se

S-7200C 8. USING THE G10 OPERATION PANEL (ADVANCED OPERATIONS) 368-3. Correction sewing When correction sewing is enabled, sewing will be carried ou

S-7200C 8. USING THE G10 OPERATION PANEL (ADVANCED OPERATIONS) 37 8-4. Thread trimming lock Thread trimming not locked Thread trimming locked

S-7200C 8. USING THE G10 OPERATION PANEL (ADVANCED OPERATIONS) 388-5. Setting the maximum sewing speed ࡮ The maximum sewing speed can be set to a s

S-7200C 8. USING THE G10 OPERATION PANEL (ADVANCED OPERATIONS) 39 8-6. Adjusting the needle up stop position 1 (While pressing the

S-7200C 8. USING THE G10 OPERATION PANEL (ADVANCED OPERATIONS) 408-7. Lock function DANGER Wait at least 5 minutes after turning off the power swit

S-7200C 9. SEWING 41 9. SEWING CAUTION Attach all safety devices before using the sewing machine. If the machine is used without thes

S-7200C 9. SEWING 429-3. Sewing condensed stitches y If you press the actuator switch (1) or the reverse lever (2) while sewing is in progress, you

S-7200C iii CAUTION Sewing This sewing machine should only be used by operators who have received the necessary training in safe use befor

S-7200C 10. THREAD TENSION 43 10. THREAD TENSION 10-1. Adjusting the thread tension CAUTION Turn off the power switch before removing or inser

S-7200C 10. THREAD TENSION 4410-2. Adjusting the presser foot pressure Correct stitches Upper thread Skipped stitches occur I

S-7200C 10. THREAD TENSION 45 10-4. Adjusting the thread take-up amount (-[][]3 specifications) CAUTION Turn off the power switch before carry

S-7200C 11. CLEANING 4611. CLEANING CAUTION Turn off the power switch before carrying out cleaning. The machine may operate if the t

S-7200C 11. CLEANING 47 2. Lubrication A. Gearbox oil quantity NOTE: y Check the quantity of oil in the gearbox immediately after tilting back the

S-7200C 11. CLEANING 48B. Oil tank oil quantity (-[]0[], []3[] specifications) Check the oil gauge window (1), and add more oil if the oil gauge (2)

S-7200C 11. CLEANING 49 11-2. Applying grease (-[]3[], []5[] specifications*) [When “GrEASEUP” appears…When using the G50 operation panel] If “GrE

S-7200C 11. CLEANING 50 1. Turn the power switch to “OFF”. 2. Remove the screws and the set screws. 3. Apply

S-7200C 11. CLEANING 51 11-3. Applying grease (-[]3[], []5[] specifications*) [When “GrUP” appears ... When using the G10 operation panel] If “GrUP

S-7200C 11. CLEANING 52 1. Turn the power switch to “OFF”. 2. Remove the screws and the set screws. 3. Apply gre

S-7200C iv [3] Warning labels The following warning labels appear on the sewing machine. Please follow the instructions on the labels at all times wh

S-7200C 12. ADJUSTING THE ROTARY HOOK LUBRICATION AMOUNT 53 12. ADJUSTING THE ROTARY HOOK LUBRICATION AMOUNT (-[]0[], []3[] specifications) CAU

S-7200C 13. STANDARD ADJUSTMENTS 5413. STANDARD ADJUSTMENTS CAUTION Maintenance and inspection of the sewing machine should only be carried

S-7200C 13. STANDARD ADJUSTMENTS 55 13-2. Adjusting the safety switch position The safety switch (1) is normally installed as shown in figure [A]. H

S-7200C 13. STANDARD ADJUSTMENTS 5613-3. Adjusting the thread take-up spring <Thread take-up spring position> The standard position of the thr

S-7200C 13. STANDARD ADJUSTMENTS 57 13-4. Adjusting arm thread guide R The standard position of arm thread guide R (1) is the position where the scr

S-7200C 13. STANDARD ADJUSTMENTS 5813-6. Adjusting of the feed dog height The standard height of the feed dog (1) when it is at its maximum height a

S-7200C 13. STANDARD ADJUSTMENTS 59 13-7. Adjusting the feed dog angle The standard angle for the feed dog (1) when it is at its highest position ab

S-7200C 13. STANDARD ADJUSTMENTS 6013-8. Adjusting the needle bar height Reference line (a), which is the second line from the bottom of the needle

S-7200C 13. STANDARD ADJUSTMENTS 61 13-10. Adjusting the needle and rotary hook timing The tip of the rotary hook (3) should be aligned with the cen

S-7200C 13. STANDARD ADJUSTMENTS 6213-11. Adjusting the treadle <Forward depression sensitivity adjustment> If the machine starts running at l

S-7200C CONTENTS 1. MACHINE SPECIFICATIONS... 1 2. NAMES OF MAJOR PARTS... 2 3. INSTALLATION...

S-7200C 14. TROUBLESHOOTING 63 14. TROUBLESHOOTING y Please check the following points before calling for repairs or service. y If the following r

S-7200C 14. TROUBLESHOOTING 64 Problem Possible cause Page 5 Skipped stitches at sewing start Thread unravelling at sewing start y Is the thread t

S-7200C 14. TROUBLESHOOTING 65 Problem Possible cause Page 8 Material slippage y Is the presser foot pressure too strong? Adjust the presser foot

S-7200C 14. TROUBLESHOOTING 66 Problem Possible cause Page 13 Broken needles y Is the material being pushed or pulled with excessive force during

S-7200C 14. TROUBLESHOOTING 67 Problem Possible cause Page 18 Nothing appears on the operation panel display. y Is the power supply connector dis

S-7200C 14. TROUBLESHOOTING 6814-2. Error code displays If an error code appears on the operation panel display 1. Make a note of the error code an

S-7200C 14. TROUBLESHOOTING 69 Error code Possible cause Page E090 Treadle connector is not connected. ࡮Is the 4-pin treadle connector inside th

S-7200C 14. TROUBLESHOOTING 70 Error code Possible cause Page E150 Motor is overheating. ࡮This is displayed when the motor becomes abnormally hot

S-7200C 14. TROUBLESHOOTING 71 Error code Possible cause Page E452 Head detector unit connection error ࡮Is the 6-pin head detector unit connecto

S-7200C 15. 7-SEGMENT DISPLAY 7215. 7-SEGMENT DISPLAY 4268M

S-7200C 1. MACHINE SPECIFICATIONS 1 1. MACHINE SPECIFICATIONS 3 4 Quick reverse O O Thread wiper - O 0 3 5 Lubrication type Minimum lub

INSTRUCTION MANUAL 15-1, Naeshiro-cho, Mizuho-ku, Nagoya 467-8561, Japan. Phone: 81-52-824-2177 © 2008 Brother Ind

S-7200C 2. NAMES OF MAJOR PARTS 22. NAMES OF MAJOR PARTS (1) Bobbin winder (2) Thread wiper (-4[